| ASKERDurometer Type D橡膠硬度計批發(fā) |
 |
 |
The Type DDurometerforhard rubber (high hardness) andplastics
橡膠硬度計批發(fā)
Used world-wide for measuring hard rubbers andplastics,andspecified in the standards of JIS K 6253, ASTM D 2240,ISO7619,DIN53505, etc. |
|
 |
| Features |
|
| 橡膠硬度計批發(fā) |
| Indentor |
 | Height: 2.50mm Shape:SharpConePoint |
|
| 橡膠硬度計批發(fā) |
| Pressure foot |
 | The Pressure foot in contactwiththespecimen is 44mm in width and 18mm in depth, wide enoughtoensureaccurate measurement.
Another type of durometer with an 18mm diameter pressurefootisavailable. In addition, the Longer Pressure Foot Type (DLType)isapplicable for measurement of narrow or concavespecimens. |
|
|
| HardnessTesterSelection Chart |  | | Our product line consistsofvarioustypes of durometers applicable to specific materials
as indicated in the chart above.
Type A Durometer (ASKER A type), conforming to JIS K 6235isthemost popular type of durometer for measuringrubberhardness.
However, verification is recommended becauseasignificantdifference is estimated to be the largest whenadurometerindicates measurement values from 10 to 90 points.
For hard specimens for which Type A Durometer readingsindicatemorethan 90 points, measurements should be undertakenusing theType DDurometer (ASKER D type). However, for softspecimenswithmeasurements of less than 20 points, the ASKER C typeor TypeEDurometer (ASKER E type) should be used. Themostimportantconsideration in using durometers is to select thecorrecttype forpurposes of measurement according to thespecimen. |
|
| Specification |
|
|
| | Standards | | JIS K 6253
JIS K 7215
ASTM D 2240
ISO 7619
ISO 868
DIN 53505 |
| | | | Indicationrange | | 0 point - 100 point (262 degree dialscale) |
| | | | Minimumindication | | 1 point (Accuracy : ±1 point) |
| | | | IndentorDesign(mm) | | Height: 2.50 30°Angle Sharp Cone PointTipRadius0.1 |
| | | | SpringForces[mN(g)] | | |
| | | | Centralholeofdiameter of Pressure foot | | Φ3 |
| | | Pressurefoot
Dimension (mm) | | 44×18(Rectangular) |
| | | | OuterDimension(mm) | | Approx. Width 57×Depth 30×Height 76 |
| | | | Weight(g) | | 200 |
| | | | Application | | hard rubber, plastic |
| |
|
| OuterDimension(mm) |
|
|  | | A custom designed pressure foot durometer isavailableaccordingto specimen conditions. |
|
| Option |
|
|  | | | Two-pointer type(max-handandactive hand) of Rubber HardnessTester
The stationary set hand (max-hand) makes the maximum valueeasiertoread and allows the creep characteristics of aspecimen.
Accurate measurement is made possible for specimens*forwhichstress relaxation occurs over time or for specimens forwhichit isdifficult to take readings from the front.
*Materials for which the reading decreases immediatelyaftertheindentor has been pressed against the surface. |
| |  | | | ConstantLoaderforDurometer
| · | Constant loarder assures uniform test pressureeliminatingfalsereadings due to differences between operators inmeasuring byhand. | | · | High accuracy and repeatability of the hardnessreadingsareassured by the flexible joint function. |
|
| |  | | | IndentorExtensionTester
| · | The gauge to check the indentor height on a durometerandthereading indicator mechanism. | | · | Inspection is conducted at 2, 50, and100pointsrespectively. |
|
| |  | | | LoadTesterforHardness Tester
| · | Tester to check load properties of the spring on a durometer | | · | Inspection is conducted at 2, 50, and75pointsrespectively. |
|
|
|
